Potable Water and Ballast Tank Coatings   Chemco have over 30 years experience in providing tank coating solutions that are guaranteed to save you money. We are market leaders and pioneers in Potable Water and Ballast Tanks coatings. Contact us for a consultation on a new build or repairs to an existing tank. Using the right system read more ►

chemco-marine.jpg

 

Potable Water and Ballast Tank Coatings

 

Chemco have over 30 years experience in providing tank coating solutions that are guaranteed to save you money. We are market leaders and pioneers in Potable Water and Ballast Tanks coatings. Contact us for a consultation on a new build or repairs to an existing tank. Using the right system for your tank will save you money and extend your asset life. Our wet tolerant coating system offers considerable time savings, cost savings and improved safety. Find out how below.

 

Potable Water Coatings

 

                              Click on pictures for larger images

Chemco’s Epoxy Potable Water Coating System is made up of two ground-breaking epoxies.  A solvent-free, wet & rust tolerant primer Epo-chem™ RS 500P. Finished off with a  solvent-free, wet tolerant, glass-flake epoxy topcoat Epo-chem™ RA 500M. A ceramic system is also available using solvent free Ceram-chem™ RP 500. This system offers a smooth like finish and is extremely hard wearing

They have been tested and approved by NATA (AS 4020:2005),  FDA and NSF. The primer is a solvent free, wet and rust tolerant primer. The top coat is also solvent free, wet tolerant and glass flake reinforced. Utilising this technology the surface can be prepared by abrasive blasting, water jetting or mechanical cleaning. Being a solvent free and wet tolerant coating, it is perfectly suited for tank linings in confined spaces. This means there is no need for  dehumidification or additional ventilation. Imagine the cost saving there alone! Chemco have solutions for concrete, ferrous or non ferrous substrates or fiberglass. The Chemco potable water protective coating has been used all around the world in Cruise ships, tankers, Container ships, deep sea fishing trawlers, Refrigeration vessels, offshore supply vessels and off shore platforms.

 

FDA Certificate for Potable Water NSF Certificate for Potable Water

 

Chemco Vinylester Potable Water Coating System Is made up of a glass-flake vinylester. 100% volume solids vinylester Chem-tect™ RB 300 is suitable for operating at high temperatures. One of the key advantages of this system is the faster cure. Faster turnaround means you can get back to work faster. This system can offer up to  a 25 years guarantee on selected systems. Not only do we have NATA (AS 4020:2005) approval but we also have 30 years of successful case studies to prove this system is a long term corrosion solution.

NATA approval – Chem-tect™ RB 300

NATA approval – Epo-chem™ RS 500P. and  Epo-chem™ RA 500M

NATA approval – Ceram-chem™ RP 500

 

                               Click on pictures for a close up

 

Speak To A Specialist Now! View All of our case studies

 

Water Ballast Tanks (WBT) Coatings

 

Water Ballast Tanks (WBT) represent the single largest  surface area on any ship. They are also areas of complex geometrical surfaces.  Normally with permanent condensation and difficult to reach confined spaces. Chemco have a unique coating system for WBT’s. It consists of a solvent-free, wet & rust tolerant primer Epo-chem™ RS 500P and solvent-free, wet tolerant, glassflake epoxy topcoat Epo-chem™ RA 500M.  This system is used world wide for new builds, refurbishment and repairs.

Don’t take our word for it though. Chemco’s solvent-free, wet & rust tolerant WBT coating system has passed independent tests for IMO Resolution MSC.215(82) for application in sea water ballast tanks on bare steel and shop primed steel. But even more appealing it has passed the same tests on wet & rusty substrates.

These areas normally suffer high levels of condensation and have difficult access. Quite often de-humidification is required, Chemco have a solution that does not require abrasive blasting. Most coating systems require abrasive blasting as the surface preparation. This presents a variety of challenges with dust, wasted abrasive removal and general health and safety. The surface preparation could be ultra high pressure water blasting, reducing many hazards and speeds up the process. Being a truly moisture tolerant epoxy it can be applied on wet and rusty surfaces, in dry dock or even at sea.

 

               Click on pictures to see how to save money and time

 

The high performance coating system has been applied all over the world now for many years. Millions of square metres of “Chemco Internationals” wet and surface tolerant coating system have been applied to ballast tanks Worldwide. Chemco are the preferred choice by many passenger and cargo carrying vessels throughout the world. Find out more by speaking to a specialist now !

 

Speak To A Specialist Now! Ballast Tank Testimonial Letter

 

ABS Certificate – Ballast Tank Maintenance Coating

Lloyds Approval – Ballast Tank Maintenance Coating – RS 500P

Lloyds Approval – Ballast Tank Maintenance Coating – RA 500M

Lloyds Type Approval – IMO Resolution MSC.215 (82) PSPC for New Build – Bare and Shop Primed Steel

 

 

Chemco Industrial Brochure Chemco Marine Brochure